Over 30 Years Experience

The Garden Hardware Experts

Instructional Videos

Instructional Videos

Firestone Building Products have a selection of training videos. These are a great aid for our customers. They have guided our customers from all over Australia to confidently carry out a do-it-yourself installation. After watching, and you are one of our customers, please feel free to contact us on 1300 733 113 for further technical expertise for fine-tuning your skills. Our 20 years experience with all aspects of this product & the processes will help you with the finer details and hints if you are not entirely confident of a perfect result.

Important considerations:

  • All detail procedures must be carried out in dry and clean conditions
  • Try to be as neat and careful as possible with your detailing. The EPDM process does not allow for silicon sealers or other patch-up products to be used. The Firestone EPDM seaming and flashing processes are very forgiving & so a fault can be easily & successfully corrected with FormFlash, SA flashing or even another panel of EPDM liner seamed into place.
  • The only cutting tool on site must be a pair of scissors with rounded-end blades. Utility or Stanley type knives should be forbidden.
  • Hint: When cutting Seam Splice Tape or FormFlash with scissors place a strip of backing tape onto the sticky side to prevent the scissors from sticking.

Video 1 of 25: How to apply 76mm QuickSeam Splice Tape


 

Video 2 of 25: Visual seam quality control inspection. Please note: You will need a crayon suitable for marking rubber for this process. Chalk will wash off and also could contaminate the repair process.


 

Video 3 of 25: Air lance visual seam quality control inspection. Please note: You will need a crayon suitable for marking rubber for this process. Chalk will wash off and also could contaminate the repair process.


 

Video 4 of 25: Air vacuum chamber visual seam quality control inspection. Please note: You will need a crayon suitable for marking rubber for this process. Chalk will wash off and also could contaminate the repair process.


 

Video 5 of 25: How to repair a wrinkle in the seam with Firestone QuicksSeam FormFlash and LapSealant HS


 

Video 6 of 25: How to patch using the Firestone QuicksSeam Repair Kit


 

Video 7 of 25: How to patch or repair a cut or large hole using the Firestone QuickSeam SA Flashing. Please Note: You must round out any areas at the end of slashes. All corners of the hole must be curve profiled with scissors to resist potential tearing.


 

Video 8 of 25: How to make a vertical seam on a cut corner using QuickSeam Splice Tape for the overlap seam, QuickSeam FormFlash at the compromised bottom corner and Firestone LapSealant HS to bead finish around the FormFlash. Please note. This cut & seam process can be eliminated by folding the surplus liner triangular pig ear of liner back in behind the liner. Folding has no detrimental effect on Firestone PondGard EPDM


 

Video 9 of 25: Installation of a Firestone QuickSeam FormFlash patch at a sharp angle-change of a seam. Please note: There must be at least 75mm coverage from the potential leak spots


 

Video 10 of 25: Making an inside corner with Firestone QuickSeam FormFlash


 

Video 11 of 25: Making an outside corner with QuickSeam FormFlash


 

Video 12 of 25: Installing a Firestone QuickSeam FormFlash patch on a QuickSeam Splice Tape overlap


 

Video 13 of 25: Installation of a Firestone QuickSeam FormFlash patch at a T joint of QuickSeam Splice Tape (Option 1). Note there must be at least 75mm coverage from the potential leak spot


 

Video 14 of 25: Installation of a Firestone QuickSeam FormFlash patch at a T joint of QuickSeam Splice Tape (Option 2). Note there must be at least 75mm coverage from the potential leak spots


 

Video 15 of 25: Making an inside corner (folded) inside a preformed concrete or timber pond, parapet or reservoir & more

Note in the video:


 

Video 16 of 25: How to terminate the liner at the waterline on a wall with a Firestone Termination Bar or similar appropriate non-corrosive flat bar


 

Video 17 of 25: How to flash a simple pipe penetration using Firestone QuickSeam FormFlash and LapSealant HS

For technical graphical details of this process, please refer to Sections 2.3.3 Page 22 of System Installation in the Firestone Installation Guidelines

This pipe flashing process requires Full Stainless Steel Hose Clamps - Click the link to our range
(Please note for large diameters, these hose clamps are piggy-backed together. e.g:  2 x GSS48 clamp suits 150mm diameter pipe)


 

Video 18 of 25: How to install a Firestone QuickSeam Pipe Flashing boot


 

Video 19 of 25: Excavation of the typical profile for a dam where the embankment will be grass covered


 

Video 20 of 25: Unrolling Firestone PondGard EPDM down an embankment


 

Video 21 of 25: Unfolding the PondGard EPDM panel by pulling and luffing


 

Video 22 of 25: Typical anchor trench for Firestone PondGard EPDM in dam applications


 

Video 23 of 25: Deploying geotextile underlay down an embankment


 

Video 24 of 25: Deploying geotextile underlay up an embankment


 

Video 25 of 25: Fastening geotextile underlay to prevent wind uplift